The Matzier Touch Series is a range of tempered glass touch products — touch light switches and touch power points (GPOs). They use a sensitive touch panel with a blue/red LED indicator for the on/off state and operate locally, with no Wi-Fi or app connection. The same GPO socket models offered in the smart range are available here, simply without the app and Wi-Fi features.

• Tempered glass panel with sensitive touch
• Blue/red LED indicator for on/off state
• Switches suit LED, incandescent and fluorescent lights, water heaters, lamp heaters and motors
• Built-in overload and overheat protection
• Minimal design suited to homes, offices and facilities

• Installation must be carried out by a licensed electrical contractor only
• Isolate the power at the switchboard before starting any work
• Recommended for indoor use
• Do not exceed the rated capacity of 10A
• Have a small flat-head screwdriver ready to open the front cover

• Touch switch base / module
• Tempered glass panel cover
• Original mounting screws

Refer to the product packaging supplied with your unit for the complete contents list.

Both touch switches and touch power points are wired with standard BV4 cable and open the same way (twist off the front cover with a small flat-head screwdriver). Connect each conductor to its matching terminal and tighten the screws.

• L (Live) to the live supply terminal
• N (Neutral) — optional; connect as required
• E (Earth) as required
• Switched outputs to terminals L1–L4 (IN / OUT)

• N (Neutral), A (Active / Live) and E (Earth) to the supply terminals
• Each socket is rated to a maximum load of 10A (2400W)
• On the GPO + 1 Gang Touch Switch, the switched light connects to the Out terminal
• On the GPO + USB-C, the USB-C charging outputs are built in — no additional mains wiring is needed for the USB port

1. Isolate the powerTurn off the circuit at the switchboard and verify it is dead.
2. Open the front coverUse a small flat-head screwdriver to twist and remove the front cover.
3. Connect the wiringSwitches: connect L (Live), N (Neutral, as required) and the switched outputs (L1–L4). Power points: connect N, A (Active) and E (Earth), plus the Out terminal on GPO + switch models. Tighten all screws.
4. Fix the unit into the wall boxLock the unit into position first, then secure with the original screws. Do not overtighten — excessive force can deform the housing.
5. Fit the glass panel coverPush the glass panel on until it clicks and is securely seated on the base housing.
6. Restore power and testTurn the main power back on. After power is on, wait 3 seconds, then touch the panel to operate.

Once the glass panel is fitted and power is restored, wait 3 seconds, then touch the panel to turn the lights on and off. The blue/red LED indicator confirms the on/off state.

• Leaving power on while testing without the glass panel fitted
• Overtightening the screws, which can deform the housing and affect operation
• Not terminating the Earth conductor on the power point (GPO) range
• Exceeding the 10A (2400W) maximum load on a socket

The Matzier smart range covers tempered glass smart switches and smart power points (GPOs), including the double GPO, GPO with an integrated 1-gang light switch, and GPO with USB-C. All connect via Wi-Fi or Zigbee through the Smart Life app and work with Apple Home, Amazon Alexa and Google Assistant.

• High-quality tempered glass panel design
• Customisable RGB LED indicator with colour selection via the app
• Built-in child lock and last-state memory after power restoration
• Adjustable backlight, dark / light app themes and energy monitoring
• Switches support 2-way to 5-way multi-control switching

• Installation must be arranged with a licensed electrical contractor only
• Isolate the power at the switchboard before starting
• Recommended for indoor use; do not exceed the rated capacity of 10A
• Have a 2.4GHz Wi-Fi network and the Smart Life app ready for setup
• Both your phone and the device must be within strong range of the Wi-Fi router

• Smart switch or power point base / module (Wi-Fi or Zigbee version)
• Tempered glass panel cover
• Original mounting screws

A Zigbee gateway is required for the Zigbee version (sold separately). Refer to the product packaging supplied with your unit for the complete contents list.

Both product types are wired with standard BV4 cable and open the same way (twist off the front cover with a small flat-head screwdriver). The terminal layout differs between switches and power points — wire to whichever applies to your unit.

• N (Neutral) and A (Active / Live) to the supply terminals
• Switched lighting outputs to the Out L1–L6 terminals
• E (Earth) as required

DIP switch & multi-way control:

• Turn the main power OFF before adjusting the DIP switch — changes won't take effect while power is on
• The 2-way switching function is enabled when the DIP switch is turned ON
• Supports up to 5-way switching; the primary 6-gang switch supports 2-way control via control cable or app association, while additional switches connect via app association only
• All active connections must be on the same phase
• Maximum total length of the S-COM and active loop cable: 50 m
• Control and load cables must not be installed together in the same conduit

• N (Neutral), A (Active / Live) and E (Earth) to the supply terminals
• Each socket is rated to a maximum load of 10A (2400W)
• On the GPO + 1 Gang Light Switch, the switched light connects to the Out terminal
• On the GPO + USB-C, the USB-C PD / QC charging outputs are built in — no additional mains wiring is needed for the USB port

1. Isolate the powerTurn off the circuit at the switchboard and verify it is dead.
2. Remove the front panel / coverUse a small flat-head screwdriver to twist and remove the front cover.
3. Connect the wiringSwitches: connect N, A (Active) and the switched outputs (Out L1–L6). Power points: connect N, A and E (Earth), plus the Out terminal on GPO + switch models. Tighten all screws.
4. Set the DIP switch if requiredSwitches only — with the power off, turn the DIP switch ON for 2-way / multi-way control and keep all actives on the same phase.
5. Fix the unit into the wall boxLock it into position, then secure with the original (or cross-head flat) screws. Do not overtighten.
6. Fit the glass panelPush the glass panel on until it clicks and is securely attached to the base housing.
7. Restore powerTurn the main power on. On switches and GPO + switch models, wait 3 seconds after power-on before touching the panel.
8. Pair in the appPress the on/off button 5 times rapidly, then hold for 5 seconds until the indicator blinks rapidly, and pair in the Smart Life app (see Testing and setup).

Download the Smart Life app

Download the Smart Life app from the App Store or Google Play, or scan the QR code printed in your product manual to install it. Make sure your phone is connected to a 2.4GHz Wi-Fi network before pairing.

Wi-Fi / Bluetooth pairing

1. Put the device into pairing modeOnce safely wired and powered on, press the on/off button 5 times rapidly, then hold for 5 seconds until the indicator blinks rapidly.
2. Add the deviceOpen the Smart Life app, tap "+", then select Electrical → Switch (BLE + Wi-Fi). With Bluetooth enabled, the device is detected automatically.
3. Connect to Wi-FiEnter your 2.4GHz Wi-Fi password and follow the on-screen prompts until pairing completes.

Zigbee pairing

Add the Zigbee gateway first (connect it to your router with the cable, then add it via "+" → Gateway). Press the button 5 times and hold for 5 seconds until the LED flashes, then add via Electrical → Switch (Zigbee), or Smart Gateway → Add Subdevice → LED Already Blinking.

Apple Home

1. Start pairingPress the on/off button 5 times rapidly, then hold for 5 seconds until the indicator blinks.
2. Add the accessoryOpen Apple Home, tap "+" → Add Accessory, then scan the setup QR code on the unit.

Alexa & Google Assistant

In the Smart Life app, go to Profile → Integrations, select Amazon Alexa or Google Assistant, then follow the on-screen steps. In the app you can control each switch or socket, monitor energy use, and set the RGB backlight, child lock and schedules. Press and hold a socket icon to access additional controls.

• Trying to connect on a 5GHz network — the device needs 2.4GHz
• Adjusting the DIP switch with the power still on (changes won't apply)
• Running control and load cables together in the same conduit (switches)
• Mixing phases across active connections in a multi-way setup (switches)
• Not terminating the Earth conductor on the GPO range
• Exceeding the 10A (2400W) maximum load on a socket
• Leaving power on while testing before the glass panel is fitted